Mrežna karta Asus NX1001 [rešeno]

Imate problem sa grafičkom karticom, monitorom, periferijama... ovo je mesto za vas

Moderator: Urednik

Post Reply

Prijatelj foruma
Prijatelj foruma
offline
User avatar

Posts: 2168
Joined: 08 Jun 2010, 13:28
Location: Centralna Srbija Kraljevo
Contact:

Post Napisano: 27 Jun 2013, 17:25


Pošto je u nedelju bilo veliko nevreme a i u blizini mene je udario grom, stradali su mu ruter (njega sam zamenio kod provajdera) i stradala mi je integrisana mrežna karta te sam kupio novu PCI Asus NX1001 mrežnu kartu.
Novu kartu nažalost ne vidi. Pošto imam dual boot na tom desktopu Slekvera i MW7, na MW7 je bilo isto stanje dok mu nisam našao drajver. Našao sam drajver i za Linuks, ali mi nikako ne polazi za rukom da ga instaliram.

Evo nekih izlaza koji će uglavnom da potvrde ovo iznad napisano, a i da vidimo kako bih mogao da instaliram taj famozni drajver.

Prvo drajver
http://support.asus.com/download.aspx?S ... 7wQUxUumGL" onclick="window.open(this.href);return false;

pa neki izlazi

Code: Select all

root@broker:/home/brok# lsmod
Module                  Size  Used by
pci_stub                 961  1 
vboxpci                15057  0 
vboxnetadp             19239  0 
vboxnetflt             16688  0 
vboxdrv               221604  3 vboxnetflt,vboxnetadp,vboxpci
snd_seq_dummy           1119  0 
snd_seq_oss            25020  0 
snd_seq_midi_event      4568  1 snd_seq_oss
snd_seq                41624  5 snd_seq_midi_event,snd_seq_oss,snd_seq_dummy
snd_seq_device          4276  3 snd_seq,snd_seq_oss,snd_seq_dummy
snd_pcm_oss            33318  0 
snd_mixer_oss          13144  1 snd_pcm_oss
ipv6                  238973  20 
lp                      7119  0 
ppdev                   4710  0 
parport_pc             16691  0 
parport                26191  3 parport_pc,ppdev,lp
fuse                   58347  11 
usbhid                 31213  0 
hid                    66141  1 usbhid
gspca_pac7302           8464  0 
gspca_main             18624  1 gspca_pac7302
videodev               66935  1 gspca_main
snd_hda_codec_via      34399  1 
nvidia               8494964  32 
snd_hda_intel          19471  2 
snd_hda_codec          70473  2 snd_hda_intel,snd_hda_codec_via
processor              22956  0 
thermal_sys            12122  1 processor
sundance               18284  0 
mii                     3335  1 sundance
psmouse                54506  0 
serio_raw               3349  0 
snd_hwdep               4898  1 snd_hda_codec
snd_pcm                59244  3 snd_hda_codec,snd_hda_intel,snd_pcm_oss
snd_page_alloc          5893  2 snd_pcm,snd_hda_intel
snd_timer              14830  2 snd_pcm,snd_seq
snd                    43944  15 snd_timer,snd_pcm,snd_hwdep,snd_hda_codec,snd_hda_intel,snd_hda_codec_via,snd_mixer_oss,snd_pcm_oss,snd_seq_device,snd_seq,snd_seq_oss
intel_agp               8712  0 
intel_gtt              11603  1 intel_agp
agpgart                21927  2 intel_gtt,intel_agp
i2c_i801                7016  0 
button                  3633  0 
evdev                   7314  7 
soundcore               4634  1 snd
asus_atk0110            8880  0 
hwmon                   1033  2 asus_atk0110,thermal_sys
i2c_core               16485  3 i2c_i801,nvidia,videodev
loop                   14683  0 

Code: Select all

root@broker:/home/brok# lspci
00:00.0 Host bridge: Intel Corporation 82G33/G31/P35/P31 Express DRAM Controller (rev 10)
00:01.0 PCI bridge: Intel Corporation 82G33/G31/P35/P31 Express PCI Express Root Port (rev 10)
00:1b.0 Audio device: Intel Corporation N10/ICH 7 Family High Definition Audio Controller (rev 01)
00:1c.0 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port 1 (rev 01)
00:1c.1 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port 2 (rev 01)
00:1d.0 USB controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #1 (rev 01)
00:1d.1 USB controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #2 (rev 01)
00:1d.2 USB controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #3 (rev 01)
00:1d.3 USB controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #4 (rev 01)
00:1d.7 USB controller: Intel Corporation N10/ICH 7 Family USB2 EHCI Controller (rev 01)
00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev e1)
00:1f.0 ISA bridge: Intel Corporation 82801GB/GR (ICH7 Family) LPC Interface Bridge (rev 01)
00:1f.1 IDE interface: Intel Corporation 82801G (ICH7 Family) IDE Controller (rev 01)
00:1f.2 IDE interface: Intel Corporation N10/ICH7 Family SATA Controller [IDE mode] (rev 01)
00:1f.3 SMBus: Intel Corporation N10/ICH 7 Family SMBus Controller (rev 01)
01:00.0 VGA compatible controller: nVidia Corporation G94 [GeForce 9600 GT] (rev a1)
04:00.0 Ethernet controller: Sundance Technology Inc / IC Plus Corp IC Plus IP100A Integrated 10/100 Ethernet MAC + PHY (rev 31)

Code: Select all

root@broker:/home/brok# lspci -v
00:00.0 Host bridge: Intel Corporation 82G33/G31/P35/P31 Express DRAM Controller (rev 10)
	Subsystem: ASUSTeK Computer Inc. P5KPL-VM Motherboard
	Flags: bus master, fast devsel, latency 0
	Capabilities: [e0] Vendor Specific Information: Len=0b <?>

00:01.0 PCI bridge: Intel Corporation 82G33/G31/P35/P31 Express PCI Express Root Port (rev 10) (prog-if 00 [Normal decode])
	Flags: bus master, fast devsel, latency 0
	Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
	I/O behind bridge: 0000d000-0000dfff
	Memory behind bridge: fa000000-feafffff
	Prefetchable memory behind bridge: 00000000e0000000-00000000efffffff
	Capabilities: [88] Subsystem: ASUSTeK Computer Inc. Device 82b0
	Capabilities: [80] Power Management version 3
	Capabilities: [90] MSI: Enable+ Count=1/1 Maskable- 64bit-
	Capabilities: [a0] Express Root Port (Slot+), MSI 00
	Capabilities: [100] Virtual Channel
	Capabilities: [140] Root Complex Link
	Kernel driver in use: pcieport

00:1b.0 Audio device: Intel Corporation N10/ICH 7 Family High Definition Audio Controller (rev 01)
	Subsystem: ASUSTeK Computer Inc. Device 83a1
	Flags: bus master, fast devsel, latency 0, IRQ 43
	Memory at f9ffc000 (64-bit, non-prefetchable) [size=16K]
	Capabilities: [50] Power Management version 2
	Capabilities: [60] MSI: Enable+ Count=1/1 Maskable- 64bit+
	Capabilities: [70] Express Root Complex Integrated Endpoint, MSI 00
	Capabilities: [100] Virtual Channel
	Capabilities: [130] Root Complex Link
	Kernel driver in use: snd_hda_intel

00:1c.0 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port 1 (rev 01) (prog-if 00 [Normal decode])
	Flags: bus master, fast devsel, latency 0
	Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
	I/O behind bridge: 00002000-00002fff
	Memory behind bridge: f4400000-f45fffff
	Prefetchable memory behind bridge: 00000000f4600000-00000000f47fffff
	Capabilities: [40] Express Root Port (Slot+), MSI 00
	Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
	Capabilities: [90] Subsystem: ASUSTeK Computer Inc. Device 8179
	Capabilities: [a0] Power Management version 2
	Capabilities: [100] Virtual Channel
	Capabilities: [180] Root Complex Link
	Kernel driver in use: pcieport

00:1c.1 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port 2 (rev 01) (prog-if 00 [Normal decode])
	Flags: bus master, fast devsel, latency 0
	Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
	I/O behind bridge: 00001000-00001fff
	Memory behind bridge: f4000000-f41fffff
	Prefetchable memory behind bridge: 00000000f4200000-00000000f43fffff
	Capabilities: [40] Express Root Port (Slot+), MSI 00
	Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
	Capabilities: [90] Subsystem: ASUSTeK Computer Inc. Device 8179
	Capabilities: [a0] Power Management version 2
	Capabilities: [100] Virtual Channel
	Capabilities: [180] Root Complex Link
	Kernel driver in use: pcieport

00:1d.0 USB controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #1 (rev 01) (prog-if 00 [UHCI])
	Subsystem: ASUSTeK Computer Inc. P5KPL-VM,P5LD2-VM Mainboard
	Flags: bus master, medium devsel, latency 0, IRQ 23
	I/O ports at c480 [size=32]
	Kernel driver in use: uhci_hcd

00:1d.1 USB controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #2 (rev 01) (prog-if 00 [UHCI])
	Subsystem: ASUSTeK Computer Inc. P5KPL-VM,P5LD2-VM Mainboard
	Flags: bus master, medium devsel, latency 0, IRQ 19
	I/O ports at c800 [size=32]
	Kernel driver in use: uhci_hcd

00:1d.2 USB controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #3 (rev 01) (prog-if 00 [UHCI])
	Subsystem: ASUSTeK Computer Inc. P5KPL-VM,P5LD2-VM Mainboard
	Flags: bus master, medium devsel, latency 0, IRQ 18
	I/O ports at c880 [size=32]
	Kernel driver in use: uhci_hcd

00:1d.3 USB controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #4 (rev 01) (prog-if 00 [UHCI])
	Subsystem: ASUSTeK Computer Inc. P5KPL-VM,P5LD2-VM Mainboard
	Flags: bus master, medium devsel, latency 0, IRQ 16
	I/O ports at cc00 [size=32]
	Kernel driver in use: uhci_hcd

00:1d.7 USB controller: Intel Corporation N10/ICH 7 Family USB2 EHCI Controller (rev 01) (prog-if 20 [EHCI])
	Subsystem: ASUSTeK Computer Inc. P5KPL-VM,P5LD2-VM Mainboard
	Flags: bus master, medium devsel, latency 0, IRQ 23
	Memory at f9ffbc00 (32-bit, non-prefetchable) [size=1K]
	Capabilities: [50] Power Management version 2
	Capabilities: [58] Debug port: BAR=1 offset=00a0
	Kernel driver in use: ehci_hcd

00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev e1) (prog-if 01 [Subtractive decode])
	Flags: bus master, fast devsel, latency 0
	Bus: primary=00, secondary=04, subordinate=04, sec-latency=32
	I/O behind bridge: 0000e000-0000efff
	Memory behind bridge: feb00000-febfffff
	Capabilities: [50] Subsystem: ASUSTeK Computer Inc. Device 8179

00:1f.0 ISA bridge: Intel Corporation 82801GB/GR (ICH7 Family) LPC Interface Bridge (rev 01)
	Subsystem: ASUSTeK Computer Inc. P5KPL-VM Motherboard
	Flags: bus master, medium devsel, latency 0
	Capabilities: [e0] Vendor Specific Information: Len=0c <?>

00:1f.1 IDE interface: Intel Corporation 82801G (ICH7 Family) IDE Controller (rev 01) (prog-if 8a [Master SecP PriP])
	Subsystem: ASUSTeK Computer Inc. P5KPL-VM Motherboard
	Flags: bus master, medium devsel, latency 0, IRQ 18
	I/O ports at 01f0 [size=8]
	I/O ports at 03f4 [size=1]
	I/O ports at 0170 [size=8]
	I/O ports at 0374 [size=1]
	I/O ports at ffa0 [size=16]
	Kernel driver in use: ata_piix

00:1f.2 IDE interface: Intel Corporation N10/ICH7 Family SATA Controller [IDE mode] (rev 01) (prog-if 8f [Master SecP SecO PriP PriO])
	Subsystem: ASUSTeK Computer Inc. P5KPL-VM Motherboard
	Flags: bus master, 66MHz, medium devsel, latency 0, IRQ 19
	I/O ports at c400 [size=8]
	I/O ports at c080 [size=4]
	I/O ports at c000 [size=8]
	I/O ports at bc00 [size=4]
	I/O ports at b880 [size=16]
	Capabilities: [70] Power Management version 2
	Kernel driver in use: ata_piix

00:1f.3 SMBus: Intel Corporation N10/ICH 7 Family SMBus Controller (rev 01)
	Subsystem: ASUSTeK Computer Inc. P5KPL-VM Motherboard
	Flags: medium devsel, IRQ 19
	I/O ports at 0400 [size=32]
	Kernel driver in use: i801_smbus

01:00.0 VGA compatible controller: nVidia Corporation G94 [GeForce 9600 GT] (rev a1) (prog-if 00 [VGA controller])
	Flags: bus master, fast devsel, latency 0, IRQ 16
	Memory at fd000000 (32-bit, non-prefetchable) [size=16M]
	Memory at e0000000 (64-bit, prefetchable) [size=256M]
	Memory at fa000000 (64-bit, non-prefetchable) [size=32M]
	I/O ports at dc00 [size=128]
	[virtual] Expansion ROM at fea80000 [disabled] [size=512K]
	Capabilities: [60] Power Management version 3
	Capabilities: [68] MSI: Enable- Count=1/1 Maskable- 64bit+
	Capabilities: [78] Express Endpoint, MSI 00
	Capabilities: [b4] Vendor Specific Information: Len=14 <?>
	Capabilities: [100] Virtual Channel
	Capabilities: [128] Power Budgeting <?>
	Capabilities: [600] Vendor Specific Information: ID=0001 Rev=1 Len=024 <?>
	Kernel driver in use: nvidia

04:00.0 Ethernet controller: Sundance Technology Inc / IC Plus Corp IC Plus IP100A Integrated 10/100 Ethernet MAC + PHY (rev 31)
	Subsystem: Sundance Technology Inc / IC Plus Corp Device 0201
	Flags: bus master, medium devsel, latency 64, IRQ 20
	I/O ports at ec00 [size=128]
	Memory at febffc00 (32-bit, non-prefetchable) [size=512]
	Expansion ROM at febe0000 [disabled] [size=64K]
	Capabilities: [50] Power Management version 2
	Kernel driver in use: sundance

Code: Select all

root@broker:/home/brok# uname -a
Linux broker 3.2.45-smp #2 SMP Sat May 18 01:20:11 CDT 2013 i686 Intel(R) Core(TM)2 Duo CPU     E7500  @ 2.93GHz GenuineIntel GNU/Linux

Code: Select all

root@broker:/home/brok# ifconfig -a
eth1: flags=4098<BROADCAST,MULTICAST>  mtu 1500
        ether 10:bf:48:e7:65:33  txqueuelen 1000  (Ethernet)
        RX packets 0  bytes 0 (0.0 B)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 0  bytes 0 (0.0 B)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0
        device interrupt 20  base 0xec00  

lo: flags=73<UP,LOOPBACK,RUNNING>  mtu 16436
        inet 127.0.0.1  netmask 255.0.0.0
        inet6 ::1  prefixlen 128  scopeid 0x10<host>
        loop  txqueuelen 0  (Local Loopback)
        RX packets 340  bytes 17320 (16.9 KiB)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 340  bytes 17320 (16.9 KiB)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0
Sadržaj drajvera

Code: Select all

compat.h  crc32.h  ethtool.h  Makefile  mii.c  mii.h  nx1001_main.c  readme.txt
Readme

Code: Select all

                ASUS NX1001 Network Adapter 
	                   Linux Driver 

Contents:
-----------
1. File Description
2. Driver Installation for Linux
3. Driver Parameter

1. File Description
-------------------

Filename                Description
====================    =======================================================
NX1001_main.c           ASUS NX1001 Network Adapter Driver Source Code.
                        This file is the main part of ASUS NX1001 Network Adapter.

compat.h                Network interface message level settings.

crc32.h                 Crc function for early Linux 2.4.19pre kernel inclusion

ethtool.h:              Defines for Linux ethtool.

mii.h                   definitions for MII-compatible transceivers.

mii.c                   MII interface library.

makefile                Make File For ASUS NX1001 Network Adapter.
                        Using "make all" for your kernel.

readme.txt              A summary of the contents for Linux Driver.
                        This file, which you are reading me now.



2. Driver Installation for Linux
-----------------------------------------
a. for kernel 2.4.x
   a1. Redhat 7.3 (linux kernel 2.4.18)
   a2. Mandrake 8.1 (kernel 2.4.8)
b. for kernel 2.6.x
c. automatically load and configure at next boot time

   a.for kernel 2.4.x
   -------------------
     a1. Redhat 7.3 (linux kernel 2.4.18)
     a1.1. install way 1:
         #make all =>generate NX1001.o
         #cp NX1001.o /lib/modules/2.4.18-3/kernel/drivers/net/
         #insmod ./NX1001.o
         #ifconfig eth0 xxx.xxx.xxx.xxx netmask yyy.yyy.yyy.yyy
            eth0 is your network adapter,use "dmesg" to check it, ex: eth0, eth1...
            xxx  is your ip address, ex: 192.168.102.211
            yyy  is your netmask address, ex:255.255.255.0

     a1.2.  install way 2:
        #make all =>generate NX1001.o
        #cp NX1001.o /lib/modules/2.4.18-3/kernel/drivers/net/
        #insmod./NX1001.o
        #setup
        [network configuration] =>to setup your ip address
        #ifup eth0
           eth0 is your network adapter, ex: eth0, eth1...	


     a2. Mandrake 8.1 (kernel 2.4.8)
       #make all  => generate Nx1001.o
       #cp NX1001.o /lib/modules/2.4.8-26mdk/kernel/drivers/net
       #insmod ./NX1001.o
       #ifconfig eth0 xxx.xxx.xxx.xxx netmask yyy.yyy.yyy.yyy
           eth0 is your network adapter,use "dmesg" to check it, ex: eth0, eth1...
           xxx  is your ip address, ex: 192.168.102.211
           yyy  is your netmask address, ex:255.255.255.0


   b. for kernel 2.6.x
   -------------------
      #make all  => generate NX1001.ko
      #insmod ./NX1001.ko (or NX1001.o)
      #ifconfig eth0 xxx.xxx.xxx.xxx netmask yyy.yyy.yyy.yyy
            eth0 is your network adapter,use "dmesg" to check it, ex: eth0, eth1...
            xxx  is your ip address, ex: 192.168.102.211
            yyy  is your netmask address, ex:255.255.255.0      
   
   c. automatically load and configure at next boot time
   -----------------------------------------------------
     c1. cp NX1001.o /lib/modules/`uname -r`/kernel/drivers/net
     *note: The `uname -r` is a command. Don't replace `uname -r` with
            2.4.18, 2.4.20smp, or some others. Must type `uname -r` directly.

     c2. Add the following lines at /etc/modules.conf:
	           
	      alias eth0 NX1001
	      options NX1001 <optional parameters>
	           	           
     c3. Run "netconfig" or "netconf" to create configuration script 

              ifcfg-eth0 located at /etc/sysconfig/network-scripts or 
              create it manually.
              [see - Configuration Script Sample]

     c4. Driver will automatically load and configure at 
              next boot time.
              
     c5. Configuration Script Sample
     ===========================
         Here is a sample of a simple configuration script:

         DEVICE=eth0
         USERCTL=no
         ONBOOT=yes
         POOTPROTO=none
         BROADCAST=207.200.5.255
         NETWORK=207.200.5.0
         NETMASK=255.255.255.0
         IPADDR=207.200.5.2
              

3. Driver Parameter
-------------------
  If you want to change the link speed, you could use parameter after 
  insmod command.
  
  insmod NX1001.o <optional parameter>    ; add parameter

  ========================================================================
   example: insmod NX1001.o media=100mbps_hd
   or	    insmod NX1001.o media=3
   or	    insmod NX1001.o media=1,2,3,4	; for 4 cards or NX1001
  ========================================================================              
  
  Parameter Description
  =====================
  You can install this driver without any addtional parameter. However, if 
  you are going to have extensive functions then it is necessary to set 
  extra parameter. Below is a list of the command line parameters supported 
  by the Linux device driver.

media=xxxxxxxxx			- Specifies the media type the NIC operates at.
				  autosense	Autosensing active media.
				  10mbps_hd	10Mbps half duplex.
				  10mbps_fd	10Mbps full duplex.
				  100mbps_hd	100Mbps half duplex.
				  100mbps_fd	100Mbps full duplex.
				  0		Autosensing active media.
				  1		10Mbps half duplex.
				  2		10Mbps full duplex.
				  3		100Mbps half duplex.
				  4		100Mbps full duplex.
				  By default, the copper devices operate at 
				  autosense, the fiber devices operate at
				  100Mbps full duplex.
				  Note that, the fiber adapter only support 
				  100Mbps half/full duplex types.	

  If wanting to change speed, this driver needed to be unloaded and reloaded with 
  new media parameter.

flowctrl=[0|1]			- Specifies the flow control function.
				  0	Disable flow control.	
				  1	Enable flow control.	
Prilikom više pokušaja na više načina, evo šta mi daje

Code: Select all

root@broker:/home/brok# cd Linux\ v1.20/
root@broker:/home/brok/Linux v1.20# ls
Makefile  compat.h  crc32.h  ethtool.h	generate  mii.c  mii.h	nx1001_main.c  readme.txt
root@broker:/home/brok/Linux v1.20# make all =>generate NX1001.o
make: *** empty variable name.  Stop.

Code: Select all

root@broker:/home/brok/Linux v1.20# make
gcc -D__KERNEL__ -DMODULE -O -Wall -Wstrict-prototypes -I/usr/src/linux/include  -DUSE_IO_OPS  -D_COMPAT_WITH_OLD_KERNEL  -c -o nx1001_main.o nx1001_main.c 
In file included from /usr/src/linux/include/linux/kernel.h:13:0,
                 from /usr/src/linux/include/linux/cache.h:4,
                 from /usr/src/linux/include/linux/time.h:7,
                 from /usr/src/linux/include/linux/stat.h:60,
                 from /usr/src/linux/include/linux/module.h:10,
                 from nx1001_main.c:187:
/usr/src/linux/include/linux/linkage.h:5:25: fatal error: asm/linkage.h: No such file or directory
compilation terminated.
make: *** [nx1001_main.o] Error 1

Code: Select all

root@broker:/home/brok/Linux v1.20# make all  => generate NX1001.ko
make: *** empty variable name.  Stop.
root@broker:/home/brok/Linux v1.20# insmod ./NX1001.ko
Error: could not load module ./NX1001.ko: No such file or directory
root@broker:/home/brok/Linux v1.20# insmod ./NX1001.o 
Error: could not load module ./NX1001.o: No such file or directory
root@broker:/home/brok/Linux v1.20# cp NX1001.o /lib/modules/`uname -r`/kernel/drivers/net
cp: cannot stat 'NX1001.o': No such file or directory



Poznata ličnost
Poznata ličnost
offline

Posts: 99
Joined: 12 Jan 2012, 10:22
Location: Novi Sad

Post Napisano: 27 Jun 2013, 19:31


Ako je ta kartica Ethernet controller: Sundance Technology Inc..., ona je već podržana u kernelu, i koliko vidim modul sundance je učitan.
Možda bi sledeće komande mogle više pomoći:

Code: Select all

# dmesg | grep eth1
$ cat /etc/udev/rules.d/70-persistent-net.rules



Prijatelj foruma
Prijatelj foruma
offline
User avatar

Posts: 2168
Joined: 08 Jun 2010, 13:28
Location: Centralna Srbija Kraljevo
Contact:

Post Napisano: 27 Jun 2013, 19:54


Bilo bi dobro da je tako, to je stara integrisana neispravna mrežna karta, takođe i modul sundance je od stare neispreavne mrežne karte.

Evo traženih izlaza

Code: Select all

root@broker:/home/brok# dmesg | grep eth1
[    8.181094] udevd[1402]: renamed network interface eth0 to eth1

Code: Select all

root@broker:/home/brok# cat /etc/udev/rules.d/70-persistent-net.rules

# PCI device 0x10ec:/sys/devices/pci0000:00/0000:00:1c.1/0000:02:00.0 (r8169)
SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*", ATTR{address}=="00:26:18:d1:aa:b3", ATTR{dev_id}=="0x0", ATTR{type}=="1", KERNEL=="eth*", NAME="eth0"



Poznata ličnost
Poznata ličnost
offline

Posts: 99
Joined: 12 Jan 2012, 10:22
Location: Novi Sad

Post Napisano: 27 Jun 2013, 20:56


Aha ok... ali lspci bi morao da ga prikaze bar kao unknown device, to zbunjuje sto nema :huh:
Takodje, 70-persistent-net.rules pokazuje da koristi r8169 modul (takodje vec podrzan u kernelu), ali lsmod ga ne prikazuje.
Probaj:

Code: Select all

# modprobe r8169
# dmesg | grep r8169
Zatim:

Code: Select all

# /etc/rc.d/rc.inet1 restart
Ako ne radi ni dalje, u /etc/udev/rules.d/70-persistent-net.rules promeni eth0 u eth1 i restartuj comp.



Prijatelj foruma
Prijatelj foruma
offline
User avatar

Posts: 2168
Joined: 08 Jun 2010, 13:28
Location: Centralna Srbija Kraljevo
Contact:

Post Napisano: 28 Jun 2013, 13:03


Nije htelo tako, ali sam uspeo da ga namestim zbog tvoje sugestije da eth0 prebacim u eth1 u /etc/udev/rules.d/70-persistent-net.rules (usput, u njemu i ne postoji eth0), ali čim sam izmenio u Wicd klijentu eth1 te je posle obeležio, nakačio sam se na mrežu. :grlj: :beer:
Evo prikaza u Wicd klijentu
screen.jpeg
Hvala puno Zero :beer:



Prijatelj foruma
Prijatelj foruma
offline
User avatar

Posts: 178
Joined: 29 Jan 2012, 18:39
Location: Novi Sad (Beočin)

Post Napisano: 28 Jun 2013, 14:40


Inace kad se menja mrezna dobro bi bilo da se rm-uje /etc/udev/rules.d/70-persistent-net.rules kako bi zaboravio karticu koje vise nema...
Open your source open your mind


Post Reply

Who is online

Users browsing this forum: No registered users and 14 guests